1. Ievads
The TP-Link TL-POE200 Power Over Ethernet Adapter Kit is designed to deliver both power and data to an Ethernet-enabled device over a single Ethernet cable. This kit is ideal for extending network connectivity to areas where power outlets are not readily available, such as for IP cameras, VoIP phones, or wireless access points. It simplifies installation by eliminating the need for separate power cables, allowing for flexible deployment of network devices up to 100 meters (328 feet) away.
2. Iepakojuma saturs
Pārbaudiet, vai jūsu iepakojumā ir šādas preces:
- PoE Injector (TL-POE200A)
- PoE Splitter (TL-POE200B)
- Power Adapter (for Injector)
- Ethernet kabelis(-i)
- Ātrās instalēšanas rokasgrāmata (nav iekļauta šajā digitālajā rokasgrāmatā)
Image: Retail box of the TP-Link TL-POE200 kit, illustrating the included PoE injector, PoE splitter, power adapter, and Ethernet cables.
3. Produkts beidziesview
The TL-POE200 kit consists of two main components: the PoE Injector and the PoE Splitter. The Injector combines power and data onto a single Ethernet cable, while the Splitter separates them at the receiving end, providing power to the connected device and data to its Ethernet port.
- PoE inžektors: Connects to your network switch/router and a power outlet. It injects DC power into the Ethernet data stream.
- PoE sadalītājs: Connects to your non-PoE enabled device. It splits the incoming PoE signal back into separate data and DC power outputs.
- Selectable Power Output: The splitter features a switch to select between 5V, 9V, or 12V DC power output, accommodating various device requirements.
- 10/100M Ethernet Ports: Both units support 10/100Mbps Ethernet speeds.
Image: The TP-Link TL-POE200 PoE Injector and Splitter units, showing their compact design and ports.
4. Iestatīšanas instrukcijas
Follow these steps to set up your TL-POE200 kit:
- Prepare the Injector:
- Connect one end of an Ethernet cable from your network switch or router to the LAN ports PoE inžektorā.
- Connect the provided power adapter to the Injector's power input port and then plug the adapter into a power outlet. The power LED on the Injector should illuminate.
- Connect Injector to Splitter:
- Run a single Ethernet cable (up to 100 meters / 328 feet) from the PoE port on the Injector to the PoE IN port on the PoE Splitter.
- Configure the Splitter:
- Before connecting your device, use the voltage selector switch on the Splitter to choose the correct DC output voltage (5V, 9V, or 12V) required by your powered device. Refer to your device's specifications for the correct voltage.
- Connect the short DC power cable from the Splitter's DC output port to your powered device's power input port.
- Connect a short Ethernet cable from the Splitter's LAN OUT port to your powered device's Ethernet port.
- Pārbaudiet savienojumu:
- Once all connections are made, your powered device should receive both power and data. Check the status LEDs on both the Injector and Splitter, and on your powered device, to confirm proper operation.
The TL-POE200 kit is designed for plug-and-play operation and typically requires no software configuration.
5. Lietošanas instrukcijas
Once properly installed, the TP-Link TL-POE200 kit operates automatically. It continuously supplies power and data through the Ethernet cable to your connected device. No further user intervention is typically required for its basic function.
- Power and Data Transmission: The system delivers 10/100Mbps data and DC power (5V, 9V, or 12V, depending on splitter setting) over a single Ethernet cable.
- Attālums: Power and data can be transmitted up to approximately 100 meters (328 feet) using a standard Ethernet cable.
- LED indikatori: Observe the LED indicators on both the Injector and Splitter for operational status. A lit LED typically indicates a successful power or data connection.
6. Apkope
To ensure optimal performance and longevity of your TL-POE200 kit, consider the following maintenance guidelines:
- Vide: Operate the devices within their specified temperature and humidity ranges. Avoid exposing them to direct sunlight, excessive heat, moisture, or dust.
- Tīrīšana: Use a soft, dry cloth to clean the exterior of the devices. Do not use liquid or aerosol cleaners.
- Kabeļu vadība: Ensure all Ethernet and power cables are securely connected and not excessively bent or strained.
- Barošanas avots: Use only the power adapter provided with the kit.
7. Traucējummeklēšana
If you encounter issues with your TL-POE200 kit, refer to the following common problems and solutions:
- Ierīcei nav strāvas:
- Ensure the Injector's power adapter is securely plugged into a working power outlet and the Injector's power LED is on.
- Verify that the Ethernet cable connecting the Injector and Splitter is properly seated and undamaged.
- Pārbaudiet sējtage selector switch on the Splitter. Ensure it is set to the correct voltage (5V, 9V, or 12V) required by your powered device. An incorrect voltage setting can prevent the device from powering on or cause damage.
- Confirm the short DC power cable from the Splitter is correctly connected to your device.
- Nav datu savienojuma:
- Check all Ethernet cable connections between your network source, the Injector, the Splitter, and your powered device.
- Ensure your network switch/router is functioning correctly.
- Verify that the Ethernet cable length does not exceed 100 meters (328 feet).
- Confirm the powered device's Ethernet port is operational.
- Intermitējošais savienojums:
- Inspect all cables for damage or loose connections.
- Ensure the operating environment is stable and free from excessive electromagnetic interference.
- Try power cycling both the Injector and the powered device.
- Saderības piezīme:
- The TL-POE200 kit is a passive PoE solution and is nē IEEE 802.3af/at compliant. This means the injector and splitter units are designed to work together as a pair and may not be compatible with other standard 802.3af/at compliant PoE injectors or splitters. Using incompatible devices can lead to damage.
8. Specifikācijas
| Modelis | TL-POE200 |
| Datu pārsūtīšanas ātrums | 10/100 Mbps |
| Ethernet porti | 2 x 10/100M Ethernet ports (Injector: 1x LAN IN, 1x PoE OUT; Splitter: 1x PoE IN, 1x LAN OUT) |
| DC Power Output (Splitter) | 5V, 9V, or 12V DC (selectable) |
| Power Input (Injector) | 48 V līdzstrāva (caur komplektā iekļauto strāvas adapteri) |
| Pārraides attālums | Līdz 100 metriem (328 pēdām) |
| Izmēri (katra vienība) | Aptuveni 3.2 collas garums x 2.1 collas platums x 0.9 collas augstums (8.1 cm x 5.3 cm x 2.3 cm) |
| Preces svars | Approximately 15 ounces (0.43 kg) for the kit |
| Darba temperatūra | 0°C līdz 40°C (32°F līdz 104°F) |
| Uzglabāšanas temperatūra | -40°C līdz 70°C (-40°F līdz 158°F) |
| Darba mitrums | 10% līdz 90% nekondensējošs |
| Uzglabāšanas mitrums | 5% līdz 90% nekondensējošs |
9. Garantija un tehniskais atbalsts
TP-Link provides an industry-leading 2-year warranty for this product. For technical assistance, please contact TP-Link support:
- Technical Support Hotline (US): +1 866 225 8139
- Technical Support Hotline (French): +1 855 987 5465
- Apmeklējiet oficiālo TP-Link vietni webvietne, kurā ir jaunākie atbalsta resursi, bieži uzdotie jautājumi un kontaktinformācija.
