1. Produkts beidziesview
This manual provides instructions for the Viqua SHO600-QL UV Lamp and Quartz Sleeve Combo Kit. This kit is designed for use with Viqua UV systems including models SPV-12, SPV-600, SP600-HO, and SC/SCM-600. The ultraviolet (UV) lamp and quartz sleeve are critical components for maintaining the effectiveness of your UV water treatment system, ensuring proper disinfection by emitting specific UV intensity.
2. Produkta sastāvdaļas
The Viqua SHO600-QL kit includes the following genuine Viqua components:
- One (1) Viqua UV Lamp: A high-output ultraviolet lamp with a proprietary stepped 4-pin configuration and a grey bulb base.
- One (1) Quartz Sleeve: A protective glass sleeve that houses the UV lamp within the UV system chamber.
Image 1: Viqua SHO600-QL UV Lamp and Quartz Sleeve. This image displays the two main components of the kit: the UV lamp with its grey base and 4-pin connector, and the clear quartz sleeve.
3. Svarīga drošības informācija
Please read and understand all safety warnings before handling or installing the UV lamp un kvarca uzmava.
- Elektrības apdraudējums: Always disconnect power to the UV system before performing any maintenance or installation.
- UV starojums: Do not look directly at an illuminated UV lamp. Exposure to UV light can cause severe eye and skin damage.
- Trauslas sastāvdaļas: UV lamp and quartz sleeve are made of glass. Handle with extreme care to prevent breakage.
- Karstās virsmas: UV lamp and surrounding components can become hot during operation. Allow the system to cool before handling.
4. Uzstādīšanas vadlīnijas
These are general guidelines. Refer to your specific Viqua UV system's manual for detailed installation instructions.
- Atvienot barošanu: Turn off and unplug the UV system from its power source.
- Izslēgt ūdeni: Close the water supply valves to the UV system to prevent water flow.
- Drenāžas sistēma (ja nepieciešams): If replacing the quartz sleeve, drain the UV chamber to avoid water spillage.
- Noņemiet vecās sastāvdaļas: Uzmanīgi noņemiet veco UV filtru.amp and quartz sleeve according to your system's instructions. Dispose of old lampir atbildīgi.
- Install New Quartz Sleeve: If replacing, gently insert the new quartz sleeve into the UV chamber. Ensure the sleeve is properly seated and sealed with the provided O-rings and retaining nut. Avoid touching the glass directly; use clean gloves or a soft cloth.
- Uzstādiet jaunu UV Lamp: Uzmanīgi ievietojiet jauno UV lamp into the quartz sleeve. Align the 4-pin connector with the lamp connector on the system's power supply. Push firmly until it clicks into place.
- Atjaunot ūdeni un enerģiju: Slowly open the water supply valves. Check for leaks. Once confirmed, plug in and turn on the UV system.
- Pārbaudīt darbību: Confirm the UV lamp indicator light is on, indicating proper lamp funkciju.
5. Darbība
Once installed and powered, the UV lamp emits ultraviolet light within the quartz sleeve. As water flows through the UV chamber, it is exposed to this UV light, which inactivates bacteria, viruses, and other microorganisms without adding chemicals to the water. The system's ballast or controller typically includes an indicator light or alarm to confirm the lamp is operating correctly or if it requires attention.
6. Apkope
Regular maintenance is crucial for the continuous effectiveness of your UV system.
- UV Lamp Aizstāšana: UV lamps have a limited effective life, typically 9,000 hours (approximately 12 months) of continuous operation. Even if the lamp appears to be glowing, its UV output diminishes over time. Replace the UV lamp annually to ensure consistent water disinfection.
- Kvarca piedurkņu tīrīšana: The quartz sleeve should be cleaned periodically (e.g., every 3-6 months, or as water quality dictates) to remove any mineral deposits or fouling that can reduce UV light transmission. If the sleeve cannot be cleaned effectively, it should be replaced.
- Use Genuine Viqua Parts: Always use genuine Viqua replacement lamps and sleeves. Non-genuine or
Saistītie dokumenti — SHO600-QL
VIQUA UVMAX Lamp un kvarca uzmavu nomaiņas instrukcijas
Visaptveroša instrukcija UV l nomaiņaiamp un kvarca uzmavas tīrīšana/nomaiņa VIQUA UVMAX H, K, H+, K+, PRO10, PRO20, PRO30 un PRO50 UV ūdens attīrīšanas sistēmās. Iekļauti detalizēti drošības brīdinājumi, soli pa solim sniegtas procedūras un apkopes padomi.
VIQUA UV Lamp un kvarca uzmavas nomaiņas instrukciju lapa
Uzziniet, kā droši nomainīt UV lamp un notīriet vai nomainiet kvarca uzmavu VIQUA UV dezinfekcijas sistēmām. Šajā instrukcijā ir aprakstīti drošības pasākumi, apkopes procedūras un pareiza dzīvsudrabu saturošu priekšmetu utilizācija.amps.
VIQUA UVMAX Lamp un kvarca uzmavas nomaiņas rokasgrāmata
Šajā instrukcijā sniegti detalizēti norādījumi UV l nomaiņai.amp un kvarca uzmavu VIQUA UVMAX ūdens attīrīšanas sistēmās, tostarp modeļos H, K, PRO10, PRO20, PRO30, PRO50, PRO24-186 un PRO24-100. Tajā ir aprakstīti būtiski drošības pasākumi un apkopes procedūras optimālai sistēmas darbībai.
VIQUA D4 UV ūdens sistēmas lietotāja rokasgrāmata un uzstādīšanas rokasgrāmata
Visaptveroša VIQUA D4 UV ūdens sistēmas lietotāja rokasgrāmata un uzstādīšanas ceļvedis, kurā aplūkota drošība, darbība, apkope, problēmu novēršana un specifikācijas. Uzziniet, kā uzstādīt, darbināt un uzturēt savu UV ūdens attīrīšanas sistēmu optimālai veiktspējai un drošībai.
VIQUA UV Lamp un kvarca uzmavas nomaiņas un apkopes instrukciju lapa
Visaptveroša instrukcija UV l nomaiņai un apkopeiamps un kvarca uzmavas VIQUA UV ūdens dezinfekcijas sistēmās, tostarp Tap, Home un Professional sēriju modeļos. Uzziniet par drošības pasākumiem, soli pa solim sniegtajām procedūrām un svarīgiem apkopes padomiem.
VIQUA UV Water Purifier Lamp and Quartz Sleeve Replacement & Maintenance Guide
This instruction sheet from VIQUA provides detailed guidance on replacing and maintaining UV lamps and quartz sleeves for various VIQUA UV water purifier models, including safety precautions and step-by-step procedures.