Izsekojams 5002CC laboratorijas taimeris

BRĪDINĀJUMI
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

Ekrāna notīrīšana līdz nullei

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

TAIMERA DARBĪBA

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

ATPAKAĻSKAITĪŠANAS LAIKA IESTATĪŠANA

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

PIEZĪME: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two examples ir dotas.

Examp1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. Nospiediet pogu 2.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Examp2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. Nospiediet pogu 3.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

SPECIFIKĀCIJAS

• Displejs: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Izšķirtspēja: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

ĀTRA ATSAUCES

• Tiek parādīts A kanāls
• B - Pirmā kanāla (1) poga
• C - Otrā kanāla (2) poga
• D - Trešā kanāla (3) poga
• E-kanāls netiek rādīts laikā vai netiek rādīts.
• F-kanāls fiksē laiku, bet netiek parādīts.
• G - Stundu (H) poga
• H- Minutes (M) button
• I – Seconds (S) button

Kanāla indikatori
LCD indicators report the status of each channel.

AKUMULATORA NOMAIŅA

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Pēc bateriju ievietošanas pārliecinieties, vai taimera displejs darbojas normāli. Laika mērīšanas laikā displejā var parādīties mirgojoši segmenti. Ja tas notiek, vienkārši atiestatiet, izņemot un atkārtoti ievietojot baterijas. Katram bateriju komplektam normālos apstākļos vajadzētu kalpot 1 līdz 2 gadus. LCD displejs paliks tukšs, kad baterijas būs jānomaina.

GARANTIJA

GARANTIJA, APKALPOŠANA VAI PĀRKALIBRĒŠANA
Lai saņemtu garantiju, servisu vai atkārtotu kalibrēšanu, sazinieties ar:

IESEKAMIE PRODUKTI 12554 Old Galveston Rd. Suite B230 Webster, Teksasa 77598 ASV

• Tālr. 281 482-1714
• Fakss 281 482-9448
• E-pasts support@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Kaķis Nr. 5002
Traceable® ir Cole-Parmer reģistrēta preču zīme.

©2020 Traceable® produkti. 92-5002-00 Rev. 6 070825

FAQ

Dokumenti / Resursi

Izsekojams 5002CC laboratorijas taimeris [pdfLietotāja rokasgrāmata 5002CC laboratorijas taimeris, 5002CC, laboratorijas taimeris, taimeris

Atsauces

• Lietotāja rokasgrāmata